Drafting a Bodice Sloper for Knits

 

At the end of Suzy’s class for a bodice sloper, she tells you how to take your woven sloper and design a knit sloper. Two slopers for the price of one!

IMG_0896

Here’s my drafted knit bodice sloper. It’s very curvy and should be tight fitting. She suggests tracing it onto colored tag (I use poster board) so that you can easily see that it is a knit sloper.

img_0961

So I did up a practice garment for a knit top because I want to make a knit flare dress. I have to check the fit first of course.

Drafting a Short Sleeve Cowl Blouse

 

I was so excited to have a sloper block so I could start drafting my own patterns! I also want to learn how to use my block to help alter readymade patterns to fit better.

I wanted to draft this cowl blouse for this lovely silk I bought at Britex Fabrics in San Francisco.   I traced my sloper and followed the directions in Suzy Furrer’s pattern drafting book to make the cowl blouse. I altered it by making the hem 1.5 inches below the waist. The rest I did by following the directions.

IMG_0891

Here’s the first pass that I whipped up in muslin. It won’t have the same drape but it give me a good start. I felt it was a little loose in the back so I think I will do the darts.

IMG_0895

Before cutting that beautiful silk, I’ll make one more sample out of less expensive fabric but one that I might still wear. I am going to drop the hemline another inch and then add a 1.5 inch hem allowance.

Not bad for the first sample.  I am going to do another one that includes the cap sleeve pattern that I will draft for it.  This process has helped me discover where there were challenges in construction as well.

I decided the hem needed to be longer and I added cap sleeves.

img_0960

Cute so far.  The final silk blouse had some challenges.  It was harder to sew than the polyester.  I used a tissue stabilizer to help feed the fabric.  I also has some problems with the hems  I have such a hard time with hems on bias cut fabric.  I think i need to just do a narrow hem and leave it at that.  I used french seams for all of the side seams except where the zipper is.  I used two layers of fabric for the sleeves so folded back on each other there is no hem.  I also added a small pleat into the cap sleeve for a little mote room.  You can’t even tell its there really but it helps with movement.  I tacked down all the facings so they didn’t flap.

 

Over all for a first drafting project this pattern turned out really nice!  I am so excited to wear it with my Style Arc Erin Culottes.

Drafting a Sloper or Pattern Block Part 5: the Sleeves

 

I decided to try a couple of sleeve tutorials as I always have Suzy Furrer and Craftsy to fall back on!

So I drafted a basic sleeve from Suzy Furrer’s book because she drafts a sleeve off the basic bodice sloper. It is a very custom sloper where the armhole curve for the back and front are often different for someone like me that has somewhat forward sloping shoulders.

Then I drafted a sleeve from Madalynne. Her tutorials are well written and thoughtful. The sloper went together easily and the back of the armhole measurement is slightly longer than the front. The only issue may be that that is doesn’t fit my bodice sloper because it is not drafted off those measurements.   It was drafted off my commercial size for the sleeve cap and then incorporated my bicep measurement and sleeve length. The layout of the blog could have been a little better as I had to constantly scroll back up to the pictures to follow the instructions.

IMG_0948

Next was a sleeve from Trantanphat. It was a totally different type of sleeve with these interesting darts at the elbow. What was unique about this tutorial, other than the darts was the fact that you enter your measurements in the first page and they calculator figures out all the other measurements for you. (It does a lot of the math!) This is kind of handy and speeds up the process immensely.   Again, this one is not based on the sloper measurements so it will be interesting to see how they fits.

IMG_0949

These should be interesting to fit into the sloper that I have from my Craftsy class.  I did use Clothing Patterns 101 tutorial for my cap sleeve. The easiest sleeve yet! We’ll see how they turn out.  There are also some good tutorials from Threads and Craftstylish.  I read those but didn’t draft them.

Now to test fit these into my sloper bodice!

Drafting a Sloper or Pattern Block 4.5: the new Bodice Muslin

 

Here is the Suzy Furrer bodice in final form on the dress form! Now I have a great set of bodice blocks. I am going to finalize them by fusing with interfacing on the back so they can stand up to a lot of use.

IMG_0866

So I learned that you make a moulage first. It is a sloper that has like a second skin fit to get the person’s exact body shape. Then she turns it in to a sloper by adding just a bit of ease to make a close fitting garmet. Suzy says you need to add this ease every time so if you do it once you have a good sloper to start all you designs from.

IMG_0890

Here’s my sloper finally done on poster board (get 2 for $1.00 at Dollar Tree!) I hang mine on a clip pant hangar in the closet or on the wall to protect it. This was so good and so much fun that I think I will go back and make new skirt and pant slopers from her book that I bought or just buy the Craftsy Class for those too!